 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| product specification 1 /32 LD420WUB ver. 1.0 42.0 wuxga tft lcd title model buyer *when you obtain standard approval, please use the above model name without suffix LD420WUB *model saa1 (rohs verified) suffix lg display co., ltd. supplier for approval specification please return 1 copy for your confirmation with your signature and comments. / / / signature date approved by ) ) ( ( final specification preliminary specification pd product development dept. lg display co., ltd j.h.kim / engineer prepared by reviewed by signature date approved by y.s. park /senior manager b.y. park / manager
product specification 2 /32 LD420WUB ver. 1.0 contents 26 handling precautions for protection film 9-6 26 appropriate condition for public display 9-7 10 signal timing specifications 3-3 25 precautions 9 25 mounting precautions 9-1 25 operating precautions 9-2 26 electrostatic discharge control 9-3 26 precautions for strong light exposure 9-4 26 storage 9-5 12 8 interface connections 3-2 color data reference 3-5 24 designation of lot mark 8-1 24 packing form 8-2 24 packing 8 23 emc 7-2 1 cover 2 contents 3 record of revisions 4 general description 1 5 absolute maximum ratings 2 6 electrical specifications 3 6 electrical characteristics 3-1 11 signal timing waveforms 3-4 13 power sequence 3-6 15 optical specifications 4 19 mechanical characteristics 5 22 reliability 6 23 international standards 7 23 safety 7-1 page item number product specification 3 /32 LD420WUB ver. 1.0 final specification - aug, 11, 2008 1.0 description page revision date revision no. record of revisions product specification 4 /32 LD420WUB ver. 1.0 general features 1. general description cn1 (51pin) lvds 2port source driver circuit tft - lcd panel (1920 rgb 1080 pixels) g1 s1 s1920 g1080 mini-lvds(rgb) timing controller [lvds rx + dcr + odc integrated] gate driver circuit eeprom power circuit block sda scl +12.0v dcr enable vbr_out back light assembly 3pinx1cn(high) 3pinx1cn(high) +24.0v, gnd, vbr-a, vbr-b status +24.0v, gnd hard coating(3h), anti-glare treatment of the front polarizer (haze 13%) surface treatment landscape and portrait enabled possible display type viewing angle free ( r/l 178 (typ.), u/d 178 (typ.) ) viewing angle (cr>10) 10bit (d) , 1.06billon colors color depth 1920 horiz. by 1080 vert. pixels, rgb stripe arrang ement pixel format 700 cd/m 2 (center 1point ,typ.) luminance, white total 174.2 w (typ.) (logic = 6.2w, inverter = 168w [vbr-a=1.65v] ) power consumption 10.5kg (typ.) weight transmissive mode, normally black display mode 0.4845 mm x 0.4845 mm pixel pitch 956.4(h) x 549.4 (v) x 53.5 mm(d) (typ.) outline dimension 42.02 inches(1067.31mm) diagonal active screen size LD420WUB is a color active matrix liquid crystal di splay with an integral cold cathode fluorescent lamp(ccfl) backlight system. the matrix employs a-s i thin film transistor as the active element. it is a transmissive type display operating in the n ormally black mode. it has a 42 inch diagonally me asured active dis pla y area with w uxga resolution (1080 ver tical by 1920 horizontal pixel array) each pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical strip es. gray scale or the luminance of the sub-pixel color is determined with a 8bit or 10-bit gray scale sign al for each dot, thus presenting a palette of more than 1. 06billion of colors. it has been designed to apply the 10-bit 2 port lvds interface. it is intended to support public display where high brightness, super wide viewing angle, high color g amut, high color depth and fast moving picture response t ime are important. bit selection vbr_ext inverter(master) inverter(slave) product specification 5 /32 LD420WUB ver. 1.0 the following items are maximum values which, if ex ceeded, may cause faulty operation or damage to the lcd module. 2. absolute maximum ratings notes : 1. temperature and relative humidity rang e are shown in the figure below. wet bulb temperature should be 39 c max, and no condensation. table 1. absolute maximum ratings v dc +5.0 0 v br brightness control voltage note 1,2 c +50 0 t op operating temperature v dc +27.0 -0.3 v bl backlight inverter lcm unit %rh 90 10 h op operating ambient humidity %rh 90 10 h st storage humidity c +60 -20 t st storage temperature v dc +5. 5 -0.3 von/off on/off control voltage at 25 2 c v dc +14.0 -0.3 v lcd power input voltage max min parameter remark value symbol 90% 10 20 30 40 50 60 70 80 0 -20 0 10 20 30 40 50 dry bulb temperature [c] wet bulb temperature [c] storage operation h u m i d i t y [ ( % ) r h ] 10% 40% 60% 60 product specification 6 /32 LD420WUB ver. 1.0 it requires two power inputs. one is employed to po wer for the lcd circuit. the other is used for the eefl backlight and inverter circuit. table 2. electrical characteristics notes : 1. the specified current and power consumpt ion are under the v lcd =12.0v, 25 2 c, f v =60hz condition whereas mosaic pattern(8 x 6) is displaye d and f v is the frame frequency. 2. the current is specified at the maximum current pattern. 3. the duration of rush current is about 2ms and ri sing time of power input is 1ms (min) mosaic pattern(8 x 6) white : 1023gray black : 0gray 3. electrical specifications 3-1. electrical characteristics 1 ma 600 520 420 1 watt 7.56 6.24 - p lcd power consumption 3 a 3 - - i rush rush current v dc 12.6 12.0 11.4 v lcd power input voltage 2 ma 820 710 600 i lcd power input current circuit : parameter symbol max typ min note unit value product specification 7 /32 LD420WUB ver. 1.0 table 3. electrical characteristics (continue) table 3. electrical characteristics (continue) 3 min 3 ts discharge stabilization time power consumption ibl_b before aging ibl_a after aging power supply input current 4 hrs 50,000 life time brightness adjust v br-a = 3.3v 2 a 10.5 9.5 - v br-a = 3.3v 1 a 8.4 7.4 - v br-a = 1.65v 1 w 192 168 - pbl v br-a = 1.65v 1 a 8 7 - 1 vp-p 0.5 - - power supply input voltage ripple v br-a = 1.65v 2 a 9.5 8.5 - 1 v bl = 22.8v v br-b = 3.3v v br-a = 1.65v a 12.0 - - irush power supply input current (in-rush) v 3.3 - 0 v br-b lamp: inverter : vdc 3.3 1.65 0.0 v br-a brightness adjust input voltage for control system signals vdc 25.2 24.0 22.8 vbl power supply input voltage on/off off on vdc 5.0 - 2.5 v on vdc 0.8 0.0 -0.3 v off parameter symbol max typ min notes unit values notes : 1. electrical characteristics are determined after the unit has been on and stable for approximately 120 minutes at 25 2 c. the specified current and power consumption are under the typical supply input voltage 24vand v br ( v br-a : 1.65v & v br-b : 3.3v), it is total power consumption. the ripple voltage of the power supply input voltag e is under 0.5 vp-p. lgd recommend input voltage is 24.0v 5%. 2. electrical characteristics are determined within 30 minutes at 25 2 c. the specified currents are under the typical supply input voltage 24v. 3. the brightness of the lamp after lighted for 5mi nutes is defined as 100%. ts is the time required for the brightness of the c enter of the lamp to be not less than 95% at typica l current. the screen of lcd module may be partially dark by t he time the brightness of lamp is stable after tur n on. 4. specified values are for a single lamp which is aligned horizontally. the life time is determined as the time which lumin ance of the lamp is 50% compared to that of initial value at the typical lamp current (v br-a : 1.65v & v br-b : 3.3v), on condition of continuous operating at 25 2 c 5. the duration of rush current is about 20ms. product specification 8 /32 LD420WUB ver. 1.0 table 4. module connector(cn1) pin configuration - lcd connector(cn1): fi-r51s-hf(manufactured by jae ) or kn25-51p-0.5sh(manufactured by hirose) - mating connector : fi-r51hl(jae) or compatible this lcd module employs two kinds of interface conn ection, a 51-pin connector is used for the module electronics and master 14-pin and slave 12-pin conn ectors are used for the integral backlight system. 3-2-1. lcd module 3-2. interface connections notes : 1. the pin no 44 is lcd test option. agp (auto gen eration lcm operates pattern) or nsb (no signal black) is case that lvds signals are out of frequen cy or abnormal condition in spite of 12 volt power supply. lpl recommends nsb. ( agp : vcc or ope n / nsb : gnd ) 2. all gnd(ground) pins should be connected togethe r to the lcd modules metal frame. 3. all vlcd (power input) pins should be connected together. 4. all input levels of lvds signals are based on th e iea 664 standard. 5. specific pins(pin no. #1~#10) are used for inter nal data process of the lcd module. if not used, these pins are no connection. 6. if dcr function should be enable(h), 10th pin must be connected to serial resistor which value is under 1k ohm. - 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 no - power supply +12.0v power supply +12.0v power supply +12.0v power supply +12.0v no connection ground ground ground no connection or gnd no connection or gnd second channel 4+ (for 10bit d) second channel 4- (for 10bit d) second channel 3+ second channel 3- ground second clock channel c+ second clock channel c- ground second channel 2+ second channel 2- second channel 1+ second channel 1- second channel 0+ second channel 0- l=8bit,h=10bit (d) description - vlcd vlcd vlcd vlcd nc gnd gnd gnd reserved reserved re4p re4n re3p re3n gnd reclkp reclkn gnd re2p re2n re1p re1n re0p re0n bit selection symbol first channel 4+ (for 10bit d) ro4p 25 first channel 4- (for 10bit d) ro4n 24 first channel 3+ ro3p 23 first channel 3- ro3n 22 ground gnd 21 first channel 1+ ro1p 15 first channel 1- ro1n 14 first channel 0+ ro0p 13 first channel 0- ro0n 12 ground gnd 11 no connection nc 2 no connection nc 3 no connection nc 4 no connection nc 5 no connection nc 6 h =jeida , l = vesa lvds select 7 external vbr vbr_ext 8 vbr output vbr_out 9 h = enable , l = disable dcr_enable 10 first channel 2- ro2n 16 first channel 2+ ro2p 17 ground gnd 18 first clock channel c- roclkn 19 first clock channel c+ roclkp 20 no connection or gnd reserved 26 description symbol no gnd ground 1 product specification 9 /32 LD420WUB ver. 1.0 table 5. inverter connector pin configulation 3-2-2. backlight inverter 2, 3 v br-a analog dimming voltage dc 0.0v ~ 3.3v (typ : 1.65v) v br- a 11 on/off 0.0v ~ 5.0v v on/off 12 4 status normal : upper 3.0v abnormal : under 0.7v status 14 v br - b gnd gnd gnd gnd gnd v bl v bl v bl v bl v bl inv. 3 backlight ground gnd 7 backlight ground gnd 8 1 burst dimming voltage dc 0.0v ~ 3.3v v br -b 13 backlight ground gnd 10 backlight ground gnd 9 backlight ground gnd 6 power supply +24.0v v bl 5 power supply +24.0v v bl 4 power supply +24.0v v bl 3 power supply +24.0v v bl 2 power supply +24.0v v bl 1 note description symbol pin no notes : 1. gnd should be connected to the lcd mod ules metal frame. 2. if pin #11 is open, v br -a = 1.65v. when apply over 1.65v( ~ 3.3v) contin uously, its luminance is increasing however lamps life tim e is decreasing. it could be usable for boost up luminance when usin g dcr (=dynamic contrast ratio) function only. 3. minimum brightness : v br -b =0v maximum brightness : v br -b = 3.3v 4. even though pin #14 is open, there is no effect o n inverter operating, the output terminal of inver ter.. 5. each impedance of pin #11,12 and 13 is 186[ ? ], 27.6[ ? ], 116[ ? ] inverter connector : s14b-ph-smc (manufactured by jst) or equivalent - mating connector : phr-14 or equivalent rear view of lcm product specification 10 /32 LD420WUB ver. 1.0 table 6. timing table (de only mode) table 6 shows the signal timing required at the inp ut of the lvds transmitter. all of the interface s ignal timing should be satisfied with the following specificatio n for normal operation. 3-3. signal timing specifications note : the input of hsync & vsync signal does not h ave an effect on normal operation(de only mode). the performance of the electro-optical characterist ics may be influenced by variance of the vertical r efresh rate. horizontal vertical lines 69 45 11 t vb blank lines - 1080 - t vv display period lines 1149 1125 1091 t vp total total blank display period t hp t hb t hv symbol 2200/2 tclk 1200 1100 1060 tclk 240 140 100 tclk - 960 - note unit max typ min item frequency vertical horizontal dclk f v f h f clk symbol hz 63 60 57 khz 68.9 67.5 65.5 148.5/2 mhz 77 74.25 70 note unit max typ min item product specification 11 /32 LD420WUB ver. 1.0 0.7vdd 0.3vdd t clk invalid data valid data invalid data invalid data invalid data pixel 0,0 pixel 2,0 pixel 1,0 pixel 3,0 de(data enable) valid data 0.5 vdd t hp t hbp t hv t hfp t vp t wv t vbp t vv t vfp hsync vsync de(data enable) de(data enable) dclk first data second data de, data t wh 3-4. signal timing waveforms * reference : sync. relation * t hb = t hfp + t wh +t hbp * t vb = t vfp + t wv +t vbp product specification 12 /32 LD420WUB ver. 1.0 the brightness of each primary color(red,green,blue ) is based on the 8-bit gray scale data input for th e color. the higher binary input, the brighter the color. ta ble 8 provides a reference for color versus data in put. table 8. color data reference 3-5. color data reference 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (000) green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 green (001) ... ... ...... ... ... ... 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 green (1022) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 green (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (000) red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 red (001) ... ... ... ...... ... ... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 red (1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red (1023) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (001) ... ...... ... ... ... ... 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (1022) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (1023) blue (000) white yellow magenta cyan blue (1023) green (1023) red (1023) black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic color 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 blue blue blue blue msb lsb green green green green msb lsb red redred red msb lsb b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 g9 g8 g7 g6 g5 g4 g3 g2 g1 g0 r9 r8 r7 r6 r5 r4 r3 r2 r1 r0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue color input color data product specification 13 /32 LD420WUB ver. 1.0 3-6. power sequence note : 1. please avoid floating state of interface signal at invalid period. 2. when the interface signal is invalid, be sure to pull down the power supply v lcd to 0v. 3. the case when the t2/t5 exceed 3x(1/fv), it oper ates protection pattern (black pattern) till valid signal inputted. there is no reliability problem. ( ex. 60hz : 3x(1/60hz) = 50ms) 4. the t3/t4 is recommended value, the case when fa iled to meet a minimum specification, abnormal display would be shown. there is no reliab ility problem. 5. if the on time of signals(interface signal and o ption signals) precedes the on time of power(v lcd ), check the lcd logic power(vcc) is under 0.8v, other wise it will be happened abnormal display. 6. t6 should be measured after the module has been f ully discharged between power off and on period. - t2 - - 5 5 2,6 3,5 4 4 3,5 notes s - - 2.0 t6 ms 0 t8 ms 0 t7 ms - - 0 t2 ms ms - - 200 t3 - - 200 t4 ms - - 0 t5 ms 20 - 0.5 t1 max typ min unit value parameter table 9. power sequence 3-6-1. lcd driving circuit interface signal (tx) power supply for lcd v lcd 10% 0v 90% 10% t 1 t 2 t 5 t 6 t 3 t 4 valid data lamp on t 7 t 8 option signal (lvds_select, dcr_enable, bit_select) 90% product specification 14 /32 LD420WUB ver. 1.0 3-6-2. sequence for inverter power supply for inverter v on/off v bl 10% 0v 90% t 1 t 2 t 3 t 2 0.7v t 4 24v (typ.) t 5 lamp on t 4 t7 1000ms (min) 1000ms (min) table 12. power sequence for inverter 3-6-3. deep condition for inverter v bl (typ.) x 0.8 0 v v bl : 24v t6 notes : 1. t1 describes rising time of 0v to 24v an d this parameter does not applied at restarting tim e. 2. t4(max) is less than t2. 3. in t7 section, vbr-b is recommended 3.3v. v bl (typ) x 0.8 ms 10 - - t6 3 ms - - 1000 t7 - ms - - 10 t5 2 ms 0 t4 1 remarks ms - - 500 t2 ms - - 200 t3 ms - - 20 t1 max typ min units values parameter v br-a & v br-b product specification 15 /32 LD420WUB ver. 1.0 lcd module optical stage(x,y) pritchard 880 or equivalent 50cm fig. 1 optical characteristic measurement equipment and method optical characteristics are determined after the un it has been on and stable in a dark environment at 25 2 c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig. 1 shows additional information concerning the measurement equipment and method. 4. optical specification table 11. optical characteristics ta= 25 2 c , v lcd =12.0v, f v =60hz, dclk=148.5mhz vbr_a=1.65v, vbr_b=3.3v 3 1.3 - - 5p white 1 - 1000 700 cr gray-to-gray - - - 7 gray scale y axis, down ( =270 ) y axis, up ( =90 ) x axis, left ( =180 ) x axis, right( =0 ) - - 89 d - - 89 u - - 89 l 6 degree - - 89 r viewing angle (cr>10) white blue green red 0.605 gy 0.285 gx 0.065 by 0.144 bx 0.292 wy 0.279 wx ms 0.333 ry typ +0.03 0.639 typ -0.03 rx color coordinates [cie1931] 4,5 14 9 - g to g response time luminance variation 2 cd/m 2 - 700 550 l wh surface luminance, white note unit contrast ratio max typ min value symbol parameter product specification 16 /32 LD420WUB ver. 1.0 table 12. gray scale specification 100 86.21 75.03 64.02 54.01 44.30 36.20 28.30 21.83 16.34 11.60 7.88 4.78 2.41 0.91 0.31 0.12 luminance [%] (typ.) l959 l1023 l639 l703 l767 l831 l447 l511 l575 l895 l191 l255 l319 l383 l127 l63 l0 gray level notes :1. contrast ratio(cr) is defined mathematica lly as : cr(contrast ratio) = maximum crn (n=1, 2, 3, 4, 5) surface luminance at position n with all white pixe ls crn = surface luminance at position n with all black pixe ls n = the position number(1, 2, 3, 4, 5). for more i nformation, see fig 2. 2. surface luminance are determined after the unit has been on and 60min after lighting the backlight in a dark environment at 25 2 c. surface luminance is the luminance value at cen ter 1-point across the lcd surface 50cm from the surfac e with all pixels displaying white. for more information see the fig. 2. 3. the variation in surface luminance , white is defined as : white(5p) = maximum(l on1 ,l on2 , l on3 , l on4 , l on5 ) / minimum(l on1 ,l on2 , l on3 , l on4 , l on5 ) where l on1 to l on5 are the luminance with all pixels displaying white at 5 locations . for more information, see the fig. 2. 4. response time is the time required for the displ ay to transition from g(n) to g(m) (rise time, tr r ) and from g(m) to g(n) (decay time, tr d ). for additional information see the fig. 3. (n product specification 19 /32 LD420WUB ver. 1.0 table 13 provides general mechanical characteristic s. 5. mechanical characteristics table 13. mechanical characteristics value item 523.25 mm vertical 10.5 kg (typ.) , 11.5kg (max.) weight 529.2 mm vertical 549.4 mm vertical 53.5 mm depth 930.25 mm horizontal active display area 936.2 mm horizontal bezel area 956.4 mm horizontal outline dimension note : please refer to a mechanic drawing in terms of tolerance at the next page. product specification 20 /32 LD420WUB ver. 1.0 product specification 21 /32 LD420WUB ver. 1.0 product specification 22 /32 LD420WUB ver. 1.0 6. reliability table 14. environment test condition note : before and after reliability test, lcm sho uld be operated with normal function. ta= 40 c ,90%rh humidity condition operation 7 0 - 15,000 ft 0 - 40,000 ft altitude operating storage / shipment 8 shock level : 50g waveform : half sine wave, 11ms direction : x, y, z one time each direction shock test (non-operating) 6 wave form : random vibration level : 1.0grms bandwidth : 10-300hz duration : x,y,z, 30 min one time each direction vibration test (non-operating) 5 ta= 0 c 240h low temperature operation test 4 ta= 50 c 50%rh 240h high temperature operation test 3 ta= -20 c 240h low temperature storage test 2 ta= 60 c 240h high temperature storage test 1 condition test item no. product specification 23 /32 LD420WUB ver. 1.0 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 methods of measurement of radio-nois e emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 b) cispr13 "limits and methods of measurement of r adio interference characteristics of sound and television broadcast receivers and associated e quipment" cispr22 "limits and methods of measurement of radi o interference characteristics of information technology equipment" international special commit tee on radio interference. c) en55013 "limits and methods of measurement of ra dio interference characteristics of sound and television broadcast receivers and associated equip ment" en55022 "limits and methods of measurement of radio interference characteristics of information technology equipment" european committee for elect ro technical standardization.(cenelec), 1988(including a1:2000) a) ul 60950-1:2003, first edition, underwriters lab oratories, inc., standard for safety of information technology equip ment. b) can/csa c22.2, no. 60950-1-03 1st ed. april 1, 2 003, canadian standards association, standard for safety of information technology equip ment. c) en 60950-1:2001, first edition, european committee for electrotechnical standardiza tion(cenelec) european standard for safety of information technol ogy equipment. d) iec 60950-1:2001, first edition, the internation al electrotechnical commission (iec) standard for safety of information technology equip ment. product specification 24 /32 LD420WUB ver. 1.0 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f : panel code g : factory code h : assembly code i,j,k,l,m : serial n o. note 1. year b) location of lot mark 2. month serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form a) package quantity in one pallet : 12 pcs b) pallet size : 1140 mm x 990 mm x 810 mm. b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 4 2 1 dec mar feb jan 8. packing mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 product specification 25 /32 LD420WUB ver. 1.0 please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using specified mountin g holes (details refer to the drawings). (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit b reak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzine. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. * there is no problem of panel crack under 5kgf / 10mm (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions 9. precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required ti me that brightness is stable after turned on) becomes longer (4) be careful for condensation at sudden temperatu re change.condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shal l be done by system manufacturers. grounding and shieldi ng methods may be important to minimized the interference. (7) please do not give any mechanical and/or acoust ical impact to lcm. otherwise, lcm cant be operated its full characteristics perfectly. (8) a screw which is fastened up the steels should be a machine screw. (if not, it can causes conductive particles and dea l lcm a fatal blow) (9) please do not set lcd on its edge. (10) it is recommended to avoid the signal cable an d conductive material over the inverter transformer for it can cause the abnormal display and temperatu re rising. (11) partial darkness may happen during 3~5 minutes when lcm is operated initially in condition that luminance is under 40% at low temperature (under 5 ). this phenomenon which disappears naturally after 3~5 minutes is not a problem about reliabili ty but lcd characteristic product specification 26 /32 LD420WUB ver. 1.0 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the te mperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. 9-5. storage 9-6. handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape . when the protection film is peeled off, static elec tricity is generated between the film and polarizer . this should be peeled off slowly and carefully by p eople who are electrically grounded and with well i on- blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel surface or its vestige is recog nized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with norma l- hexane. 9-7. appropriate condition for public display - generally large-sized lcd modules are designed for consumer applications (tv). accordingly, a long-term display like in public dis play (pd) application, can cause uneven display inc luding image sticking. to optimize module's lifetime and f unction, several operating usages are required. 1. normal operating condition - temperature: 0 ~ 40 - operating ambient humidity : 10 ~ 90 % - display pattern: dynamic pattern (real display) note) long-term static display can cause image stic king. 2. operating usages under abnormal condition1 a. ambient condition - well-ventilated place is recommended to set up pd system. b. power and screen save - periodical power-off or screen save is needed afte r long-term display. product specification 27 /32 LD420WUB ver. 1.0 3. operating usages to protect against image sticki ng due to long-term static display a. suitable operating time: under 18 hours a day. b. static information display recommended to use wi th moving image. - cycling display between 5 minutes' information(sta tic) display and 10 seconds' moving image. c. background and character (image) color change - use different colors for background and character, respectively. - change colors themselves periodically. d. avoid combination of background and character wi th large different luminance. 1) abnormal condition just means conditions except normal condition. 2) black image or moving image is strongly recommen ded as a screen save. 4. lifetime in this spec. is guaranteed only when p d is used according to operating usages. product specification 28 /32 LD420WUB ver. 1.0 r10/r20 r11/r21 r12/r22 r13/r23 r14/r24 r15/r25 r16/r26 r17/r27 g10/g20 g11/g21 g12/g22 g13/g23 g14/g24 g15/g25 g16/g26 g17/g27 b10/b20 b11/b21 b12/b22 b13/b23 b14/b24 b15/b25 b16/b26 b17/b27 hsync vsync data enable clock host system 24 bit ta1-ta1+ tb1-/tb1+ tc1-/tc1+ tclk1- tclk1+ td1-/td1+ ta2-/ta2+ tb2-/tb2+ tc2-/tc2+ tclk2- tclk2+ td2-/td2+ thc63lvd823 or compatible rxo0- rxo0+ rxo1- rxo1+ rxo2- rxo2+ rxoclk- rxoclk+ rxo3- rxo3+ rxe0- rxe0+ rxe1- rxe1+ rxe2- rxe2+ rxeclkin- rxeclkin+ rxe3- rxe3+ vesa / jeida dcr enable fi-r51s-hf timing controller lcd module ground 49 48 47 46 40 39 44 43 42 41 37 35 31 30 36 34 32 29 28 27 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 12 13 14 15 16 17 19 20 22 23 28 29 30 31 32 33 35 36 38 39 7 10 53/81 54/82 57/83 58/84 59/85 60/86 51/79 52/80 63/91 64/92 65/93 66/94 67/95 68/96 61/89 62/90 73/99 74/100 75/1 76/2 77/5 78/6 69/97 70/98 7 8 9 10 # appendix-i-1 required signal assignment for flat link (thine : t hc63lvd823) transmitter(pin7=l) notes: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd823 or compatible) 3. 7 means msb and 0 means lsb at r,g,b pixel dat a. product specification 29 /32 LD420WUB ver. 1.0 r10/r20 r11/r21 r12/r22 r13/r23 r14/r24 r15/r25 r16/r26 r17/r27 g10/g20 g11/g21 g12/g22 g13/g23 g14/g24 g15/g25 g16/g26 g17/g27 b10/b20 b11/b21 b12/b22 b13/b23 b14/b24 b15/b25 b16/b26 b17/b27 hsync vsync data enable clock host system 24 bit thc63lvd823 or compatible 51/79 52/80 53/81 54/82 57/83 58/84 59/85 60/86 61/89 62/90 63/91 64/92 65/93 66/94 67/95 68/96 69/97 70/98 73/99 74/100 75/1 76/2 77/5 78/6 7 8 9 10 ta1-ta1+ tb1-/tb1+ tc1-/tc1+ tclk1- tclk1+ td1-/td1+ ta2-/ta2+ tb2-/tb2+ tc2-/tc2+ tclk2- tclk2+ td2-/td2+ rxo0- rxo0+ rxo1- rxo1+ rxo2- rxo2+ rxoclk- rxoclk+ rxo3- rxo3+ rxe0- rxe0+ rxe1- rxe1+ rxe2- rxe2+ rxeclkin- rxeclkin+ rxe3- rxe3+ vesa / jeida dcr enable fi-r51s-hf timing controller lcd module vcc 49 48 47 46 40 39 44 43 42 41 37 35 31 30 36 34 32 29 28 27 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 12 13 14 15 16 17 19 20 22 23 28 29 30 31 32 33 35 36 38 39 7 10 # appendix-i-2 required signal assignment for flat link (thine : t hc63lvd823) transmitter(pin7=h) notes: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd823 or compatible) 3. 7 means msb and 0 means lsb at r,g,b pixel dat a. product specification 30 /32 LD420WUB ver. 1.0 # appendix-ii pallet assy steel band,clip 9 pp band 10 yupo 80g 100x100 label 11 paper angle,packing 8 paper 1140x990x130mm pallet 4 masking 20mmx50m tape 3 eps packing,top 6 eps packing,bottom 5 paper angle,post 7 42inch bag 2 lcd module 1 material description no. product specification 31 /32 LD420WUB ver. 1.0 # appendix 2 # appendix- iii lcm label 8 serial no. (see cas 24page for more information) 1 2 3 4 5 6 7 9 10 11 12 inch m assy factory code serial no. 13 month year model serial no. ul, tuv mark lpl logo us patent no. origin rohs verified made in korea LD420WUB (sa)(a1) product specification 32 /32 LD420WUB ver. 1.0 # appendix 3 # appendix- iv pallet label LD420WUB saa1 12 pcs 001/01-01 made in korea rohs verified xxxxx xxxxxxxx xxx xxx xxxx |
Price & Availability of LD420WUB
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |